ELMconfig USB device 500kbit/s ELM327 compatible interface with MS-CAN switch for Forscan FoCCCus OBD2 diagnostics …

Product Information

EDIT* NOTE PuTTy is not needed for ELMconfig Program , once Elm327 is connected then select configure from the menu on startup of ELMconfig , this will send all commands to re-configure your ELM327. I've explicitly set the adapter to use 500,000bps in ELMConfig, and it confirms that setting in the window titlebar.

I've copied and pasted this reply I had off @Dan P that sorted out my problems when I was having trouble, he was excellent, fair play to him. Before you modify the interface I suggest you get the Elm interface and the program working and talking to your car before modifying it so you can then access all modules.

How to Setup your ELM327 with Elmconfig

ELMConfig can't open a connection to the adapter at all, no matter which mode or laptop I try (Yes, FORScan is closed when I try to use ELMConfig). In all cases, it pops up an error saying "Correct response from adapter timed." Usually, the request and response are both empty, as in this screenshot I took: The FoCCCus software is originally developed for the Focus MK3. The original developer of the FoCCCus software stopped developing the software any further about 3 Years ago. I have a Ford Focus MK2 2.0 l petrol car. I tried for curiosity to write the odometer on my car, I was able to increase the km value, but not to decrease it from the “odometer write” menu. Than I tried to use the menu under IC programming, called “write odometer value in km” or so. As I wrote the former value from this menu, the decreasing also didn’t succeeded, but many problems came instead of. I've read that this step takes other people closer to 5 minutes, once the setup is correct, so I'm trying to figure out where I went wrong.

Solder pin 6 (which you just de-soldered) to the middle pin on your switch (middle bottom in diagram) You cannot read and erase error codes with this software. This software is used for configuring many ECU parameters. Very powerful software but a limited number of supported vehicles. Please FIRST move the unextracted folder to your Desktop, else below #2 step won't show "Install" option.

ELM327 WiFi Software for iOS Apple Devices

Having connected the ELM327 module to the PC USB port and car OBD port and launched Forscan, I switched the ignition on when prompted – on my keyless start model this meant pressing the power button without pressing the clutch Actually the FW for the 140 & 163 is the same and just a couple of bits tell the ECU that is has to use the maps for the 140 resp 163 engine. Turn on the car ignition but don’t start the engine! At this point, you can launch the ELM327 software. It will automatically detect the OBD2 reader and the vehicle ECU.

Please note, if you’re looking for OBD2 software for Windows Laptop/PC, these will not work. You’ll need to look into some software like PCMScan or AutoEnginuity if you want to use a USB ELM327 with your laptop. These are the modules available to you in ELMConfig, most of them are pretty self explanatory. Not all modules will be fitted to all cars, for example, only the Kuga will have the AWD module. If your car doesn’t have a module, it doesn’t mean that it can’t be fitted and the functionality added to your car. There have been success stories of people adding cruise control to cars, and enabling it using ELMConfig. MS-CAN GEMFORScan Lite for Android - attention: some functions are missing in FORScan Lite. Please see comparison of applications Install USB drivers for your ELM327 ( you may have to search for WIN 7 drivers) but it does work on Windows 7 What i will attempt to do is a guide for the FF2 (russian program) which will allow you to plug in a ELM 327 interface code reader into your focus Mk2 / Mk2.5 and update various parts of your car. Got the long list above after the car decided to not talk to the PATS module I think and immobilized. Reset fault codes and it seemed happy then

improvement in ABS Service Bleed function (replacing with function that has ability to bleed individual components) for: If you want to configure modules,many of the BT units will fail and refuse without OBD2 adapter to progarm them. This is the main screen of ELMConfig – Along the left hand side is the main module navigation, with the Low CAN & High CAN modules. Below this, you can read the fault codes within each module, and also clear the codes to prevent the warning lights showing. Solder pin 14 (which you just de-soldered) to the other middle pin on your switch (middle top in diagram)

Need to know which software to download to use your wireless OBD2 scanner?

HS-CAN mode. Needs two modules to modify. (This was already enabled from factory on mine but this how you do it) It is advisable that no other USB devices are connected to your computer. Select the correct COM port where the vLinker FS is connected. If there are multiple usb devices connected to your pc, you will need to determine which one is correct from the Device Manager. ELMConfig is a piece of software written by Russian enthusiast Sergey, known as civil-zz. It started life with an application called FF2, which allowed you to alter modules in a, surprisingly, Ford Focus Mk2. ELMConfig was written along-side, but soon did everything FF2 did and more. FF2 was retired, ELMConfig took over, was enhanced, and added functionality to work with more versions of modules. The software was then translated into English. You can thank Sergey for his hard work by making a donationto him. Basics Service functions HVAC "Actuators Calibration","Reset the Outside Air Temperature Sensor Learned Values" for: You cannot read and erase error codes with this software. It does mostly same stuff as ELMconfig but has a different selection of vehicles. Do not use this software if you are not sure what you are doing.